- Certification: CE,ISO9001,TUV,UL,BV,ETC.
- Use: Surface preparation/Smoothing/Decorative blasting/Peening/De-burring
- Port: QINGDAO/TIANJIN/SHANGHAI
Tunnel overhead conveyor shot blasting machines with monorail
Blasting Effect Comparison
Steel Structural Works Before
Blast cabinet• Welded by steel plates and profile steel, have enough strength and rigidity.
• ZGMn13 steel guard plate, which is hard enough to deal with the shot blasting from 35HRC to more than 55HRC.
• High impact toughness can make full use of the reflection kinetic energy of shot to continue to blast cleaning the surface of work piece, so greatly enhance the cleaning efficiency and quality.
• High chrome wear resistant cast iron grate guard plate which protect the screw conveyor and prevent big clump to get into the hopper damaging the bottom screw conveyor
Blast turbines• Cantilever centrifugal high efficiency blast wheel, can operate clockwise or counter-clockwise, optimum abrasive flow rate for faster cleaning.
• impeller adopted #40 Chrome wear resistant cast iron.
• High chrome wear resistant cast iron for blades, control cage, abrasive distributor.
• Dynamic and static balance.
• Blades of impeller weight tolerance≤±1.5g.
• Unbalanced torque tolerance≤±7.5Nmm.
• Direct drive blast wheel with special motor bearings means less spare parts, less noise, energy-efficient, large abrasive flow rate and good cleaning effect ,etc. advantages.
• Machined housing ensures proper alignment of all internal parts.
• Less part wear due to greater concentricity and more precise alignment.
• Safety interlock is fitted on the housing cover to protect the workers safety.
• Particular guard liner structure increase the abrasion resistant lifespan 60% to 200%.
Pneumatic Abrasive dosing units• Patented pneumatic control abrasive gate valve, which depend on cylinder to control stroke so as to control the blast wheel in long-distance. This avoids motor burned, blast wheel jammed, shot idling blast and people injured caused by common abrasive control valve closure lax
• Abrasive flow is indicated at the ammeter at the electrical switch and control box.
• Adjusting the bolt on the abrasive control valve can conveniently adjust the abrasive flow rate to an required amount
• In order to be able to dismount the abrasive control unit from the silo for repair works and to avoid any abrasive outflow for each unit one manual slide is installed in front of the abrasive control unit.
Our patented abrasive separator consists of an extended rotary separator drum that will totally remove all big clumps including big wast, scrap and paint chips etc. The abrasive is then fed through a gravity air wash separator where all dust, degraded abrasive and waste is drawn out of hte good abrasive by an air current.
Only good, correctly sized abrasive is fed back to the abrasive storage hopper and blast pots for recycling.
Our patented abrasive cleaner ensures maximum recyling rates of the abrasive and high quality surface finishing is achieved.
|Machine type:||HTK 04/05||HTK 08/09||HTK 12/09||HTK 12/11||HTK 12/11Q|
|Max. workpiece dimension ø x b (mm)||300*600||500*1200||800*2000||1000*2500||1200*3000|
|Max height (mm)||4700||5900||6700||7200||7700|
|Max width (mm)||4200||5100||5900||6100||6300|
|Max length (kg)||5000||8500||8500||10500||10500|
|No. of wheels x power (KW)||4x 7.5||8x7.5||12x11||12x 11||12x 11|
|Total installed power(KW)||41||72||143||147||157|
|Exhausted air quantity (m3/h)||6000||12000||18000||22000||25000|
Abrator, blast descaling machine, blast machines, blast cleaning machine, shot blasting equipment manufacturers, abrasive blasting machine, industrial shot blasting machine, abrasive blasting equipment, shot blaster, Tunnel shot blasting machine, bicycle frames shot blasting machine, motorbike frames shot blasting machine, truck coaches shot blasting machine, moulds shot blasting machine
If you have any suggestions or opinions about our products,please leave a message,and we will immediately answer your questions. Thanks for your support.